Page 205 of 1073
Re: What did you do to your van today?
Posted: Sun Oct 18, 2015 6:52 pm
by Caddyshack57
Re: What did you do to your van today?
Posted: Sun Oct 18, 2015 7:05 pm
by torque777
Doc's the man for this
Re: What did you do to your van today?
Posted: Sun Oct 18, 2015 7:26 pm
by maxx007at
MartyPL wrote:Mainland Europe has RHT (right hand traffic) with LHD (left hand drive) vehicles and the UK has LHT with RHD vehicles.
So ... Yes. My steering wheel is on the left side and that's what LHD means:) or maybe it means where the driver seat is;) Doesn't matter. We are LHD;)
Allrighty then. Could you share the partnumbers for the mirrors then?
Re: What did you do to your van today?
Posted: Sun Oct 18, 2015 8:47 pm
by paul4314
[quote="Caddyshack57"]Got myself these items to fit on my Caddy today ,,,, Well pleased
Problem now is I need someone to fit and re code them for me
shame I don't have any software to do the immobiliser or I could have helped u out
U already got a cruise control stalk if not get one also what years the van
Re: What did you do to your van today?
Posted: Mon Oct 19, 2015 7:32 am
by chrisellis211
pounder770 wrote:ImageUploadedByTapatalk1442423516.447579.jpg
ImageUploadedByTapatalk1442423529.988743.jpg
ImageUploadedByTapatalk1442423543.776548.jpg
Skoda Superb interior light ... Similar to Passat W8 but only a tenner at the breakers!!
How easy was this to wire up?
Re: What did you do to your van today?
Posted: Mon Oct 19, 2015 7:40 am
by pounder770
Easy enough, there's a guide on here somewhere!
Re: What did you do to your van today?
Posted: Mon Oct 19, 2015 4:19 pm
by Caddyshack57
paul4314 wrote:
Its 05 reg mate , no I've not got a cruise control stalk
do I need to change both stalks to add this one ? or does it replace my indicator stalk ?
Re: What did you do to your van today?
Posted: Mon Oct 19, 2015 5:06 pm
by Caddyshack57
Re: What did you do to your van today?
Posted: Mon Oct 19, 2015 9:04 pm
by horace01
Nice. I've seen a few of these kits available. Looks good.
Re: What did you do to your van today?
Posted: Mon Oct 19, 2015 10:31 pm
by paul4314
Caddyshack57 wrote:
Its 05 reg mate , no I've not got a cruise control stalk
do I need to change both stalks to add this one ? or does it replace my indicator stalk ?
It will replace your indicator stalk u need to look for the comprehensive cruise control fitting guide as I think the 2005 needed an extra wire fitting to make cruise function when activated u may a swell go the whole nine yards if ur doing mfsw and midline cluster
Re: What did you do to your van today?
Posted: Mon Oct 19, 2015 11:09 pm
by Caddyshack57
horace01 wrote:Nice. I've seen a few of these kits available. Looks good.
Cheers Horace01,
I'm pleased with it and not that expensive
Re: What did you do to your van today?
Posted: Mon Oct 19, 2015 11:14 pm
by Caddyshack57
Paul,
Would you know If the vehicle that I got the mfsw and midline cluster from would be suitable as it is available to buy still at £35.00 (golf mk5 2007)
Re: What did you do to your van today?
Posted: Mon Oct 19, 2015 11:26 pm
by horace01
Caddyshack57 wrote:Cheers Horace01,
I'm pleased with it and not that expensive
Can i ask where you got yours? Im wanting a carbon set myself to replace the hack carbon job I did myself
Re: What did you do to your van today?
Posted: Tue Oct 20, 2015 12:10 am
by billstein9
Today I figured out a use for all the cup holders in the caddy and that the wired slot pocket by the handbrake fits a nougat wafer ice cream pretty well!
Re: What did you do to your van today?
Posted: Wed Oct 21, 2015 5:47 pm
by Geraout
S.w.blackwell wrote:
I used 5mm flat top wide angle red leds, I have these from other projects but you can get them from RS, FARNELL, CPC, MAPLIN (don't forget an inline resistor)
The passenger door I added a Tamiya 2 pole connector (left over from something else so the door card can be removed)
They go to pin 17 as shown by the yellow wire and share the -Ve (pin 19) from the door warning lights. (note my van is 2015 Black edition / highline)
I had to use VCDS on the door modules to get them to work. (think it was +8, but it is listed on the helper)
may have more pics on camera if wanted.
steve
Looks good !
Can you say what inline resistor is required pls?
