Page 2 of 2
Re: Torque settings
Posted: Sun Aug 18, 2019 2:28 pm
by Novakid
Adie66 any chance u could send me torque settings for flywheel bolts not dmf
Cheers
Sean
Sent from my SM-G965F using Tapatalk
Re: Torque settings
Posted: Sun Aug 18, 2019 2:39 pm
by Adie66
Yeah are you running a smf ?
Sent from my SM-G973F using Tapatalk
Re: Torque settings
Posted: Sun Aug 18, 2019 3:16 pm
by Novakid
Cheers mate
Yeah the BLS had the single and was replaced about 20k ago.
Sent from my SM-G965F using Tapatalk
Re: Torque settings
Posted: Sun Aug 18, 2019 3:20 pm
by Adie66
Ok ive the torque setting for my smf on mine there slightly different to the ones in the book
Thats what came with mine an its a valeo smf conversion on my van also have you got new bolts and thread lock ?
Sent from my SM-G973F using Tapatalk
Re: Torque settings
Posted: Sun Aug 18, 2019 4:39 pm
by Novakid
Will get new bolts from tps and thread lock from work , thanks again.
Getting excited now been bolting all the parts back together and giving them a good scrub a polish before going back on.
Sent from my SM-G965F using Tapatalk
Re: Torque settings
Posted: Sun Aug 18, 2019 4:40 pm
by Novakid
Adie66 wrote:Ok ive the torque setting for my smf on mine there slightly different to the ones in the book
Thats what came with mine an its a valeo smf conversion on my van also have you got new bolts and thread lock ?
Sent from my SM-G973F using Tapatalk
Sorry forgot to say what's with the green arrows ?
Sent from my SM-G965F using Tapatalk
Re: Torque settings
Posted: Sun Aug 18, 2019 4:47 pm
by Adie66
The green arrows are for the pressure plate to make sure it on the correct way
That may not apply to yours unless its the same clucth kit as mine
Sent from my SM-G973F using Tapatalk
Re: Torque settings
Posted: Sun Aug 18, 2019 4:49 pm
by Adie66
Novakid wrote:Will get new bolts from tps and thread lock from work , thanks again.
Getting excited now been bolting all the parts back together and giving them a good scrub a polish before going back on.
Sent from my SM-G965F using Tapatalk
Sound good mate hope all goes well for you an you need any info or anything else im happy to help out
Sent from my SM-G973F using Tapatalk
Re: Torque settings
Posted: Sun Aug 18, 2019 4:49 pm
by Novakid
Having a moment sorry, I believe I have a duel mass flywheel. Apologies been in the back of the van to get it.
Sent from my SM-G965F using Tapatalk
Re: Torque settings
Posted: Sun Aug 18, 2019 4:52 pm
by Adie66
Thats a dual mass flywheel
It would be good practice to change it while its off but if you said its only done 20k should still be good
Clucth cover bolts 10nm or 7 lbf ft
Flywheel dmf
Stage 1 60nm or 44 lbf ft
Stage 2 angle tighten 90 degrees
Re: Torque settings
Posted: Sun Aug 18, 2019 5:00 pm
by Novakid
Thanks Adie66 life saver.
Yeah I have the invoice for it so just over 20k
Sent from my SM-G965F using Tapatalk
Re: Torque settings
Posted: Sun Aug 18, 2019 5:03 pm
by Adie66
No worries mate i have a full Haynes manual for the caddy and i have one for the asz as well helped me loads i would recommend getting one there just under 15 quid on ebay if i remember correctly
Sent from my SM-G973F using Tapatalk