What did you do to your van today?

[DeanWhit]

Waved mine off today after selling it. A bit gutted but onwards and upwards.

Plus, I can also do another one!!

[Biggerbelly]

Purchased speaker upgrades including sub and amp, power cable run from battery in preperation.

Thank you to Peter at https://www.scrdistribution.co.uk/.

[petrev]

Finally !

Is it just me ? Probably.

Got rid of the stupid baby seat warnings from my LHS sun visor

.

And relax.

Why don't they just put a warning sign on the baby seat ?
Why make everyone look at the stupid warning when ~99.999% of journeys are made without a rearward facing baby seat in the front passenger position
(Statistic for illustrative purposes only)

[Step83]

Not today, but this week I put in an induction kit, and an air freshener.

Induction kit with the remap seems decent. Not sure if I want to go to the effort of a BOV but tempted to get a larger air intercooler though.

[gorelimey]

Took the dash out, Touran is 90% in. To do:

* Worry that the steering will be straight because I forgot so mark it.
* Glovebox
* Bent bracket on drivers side
* Recirculation flap motor fix or replace
* Fight with trh A pillar trim

[Poffe]

Disassembled every panel and trim above the dashboard. Then scuffed it up, painted with plastic primer, acrylic paint ( RAL7024 grafite grey) and the 2k matt clear coat. Hope the colour will match with all the other trim panels. Didn’t like the two tone interior with light colours.




Sent from my Nokia 3310

[stu_b]

Looks like a nice result
You should be happy with the new colour n matching

[Poffe]

Looks like a nice result
You should be happy with the new colour n matching

Thx Stu_b! Im looking forward to get it back in the car.

[Fschwep]

Cut off one section of the rear axle bump stops. They were so close the van practically sat on them all the time. Not a lowered suspension, but I replaced old tattered bump stops with a set that were too long (I did not know at the time you could get them in different lengths, an,d they were described as being suitable for my vehicle spec). Basically, once we were sitting in it with two people the van just rode on the stops and bounced all over the place at the slightest undulation or tiny ridge, like an asphalt repair patch. Got us back pain.
It's a lot better now, the car has some travel again and rides more comfortable. And it was thanks to this forum I found that many people just cut off a bit to maintain some travel when they lower their suspension. Meaning they can actually be shortened without risk. So, thanks guys!
I have no ramp or lift so it was a bit of a hassle on my back under the car. OK on the left, more of a wrestle on the right where the exhaust sits in the way. My pot belly sat pretty tight under the side. Hum. But I got it done without needing to jack it up and take the wheels off one by one. Used a pruning saw as the new stops are heavy duty PU ones weighing a pound each, not thin rubber like the originals...

Before:


After:


Bits and tool used:

[Step83]

Made a new rear inner barn door panel for the smaller door using some 6mm ply,

Then added a trimmed own Molle back seat storage thing and spaced it using 20mm spacers. nice bit of storage space. Can't upload a photo at the moment Flickr is having a moment.

[adeybroth]

Well, I’ve actually done nothing thanks to Direct Line, was about to change my std 16” wheels to 18s, only to be told that they cannot insure me if I make the change FFS


Sent from my iPhone using Tapatalk

[raitis]

Did some rust repair on the spare wheel holder bits that were on the van already from factory and fitted the missing pieces to finally store a full-size spare under the floor. Also changed the heat shield above the muffler as the old one barely held in place and resonated horribly at certain RPM's. Left a lot of the underside rust untreated as there's too much of it requiring taking off the fuel tank and sandblasting on a lift.

[pd2h]

My breaker bargain £4 Polo rear belts fitted to replace the crappy looking touran ones.

Sent from my Pixel 4a using Tapatalk

Hey how do those get mounted from the inside out please?

[Dextersaurus]

I finally got round to fitting the set of MK1 Audi TT seats I picked up mega cheap





Reading online this was totally impossible and not even worth attempting. Don't know what all the fuss was about really. That's them in, full range of movement available on them and they actually hold me in place when I go round a corner.

Amazing

[Ollie_B_2000]

Just replaced the lower door slider as the previous wheel had disintegrated and it was digging into the paint. Super simple job and a £15 part, well happy!